Article 0
Hello there, I have a question that maybe you can help me put with, I've not been running a CMM for about 4 years now last week got back into it. I have created a program for a part which it ran...
View Article2d Vs. 3d Vs. Cylinder alignment
Just want some thoughts from all you experts out there....If I have a part that has -A- (a Circle 1.00") on one end and -B- (also a Circle .500") on the other end. and I have a runout to A-B. Which...
View ArticleError message: exception has been thrown by the target of an invocaton
New to DataPage+. I am trying to create a custom report. I have selected the features and transactions. Pressed the apply button and gone to the Text tab and create custom excel report. I selected by...
View ArticleStop Inspect from creating a report
I've just started playing with Inspect for the first time. I think it's a very good idea and will make a big difference to me since I'm going to have potentially a dozen different operators that I...
View ArticleLooping question: Unique Input for Each Part plus Skipping Stations
I'd like to write a program capable of inspecting 4 identical parts mounted to fixtures, pitched 100mm apart from one another. The user will be asked where each part came from (location on on the CNC...
View ArticleMultiple variables
Hi, I have 34 variables and each one of them represents a z-value. These variables I use in a loop, and every run the loop uses one variable, however, I want to move the variable to the next variable...
View ArticleAuto Output of Report: view last execute report mode
I am just going to throw this out there since I can't find anything through searching and I am continuing to look through the help file. I am sending pdf reports, text only, to a network drive location...
View ArticleProbe Calibration Parameters
I have searched the forum extensively on this topic and found a lot of good information but I am still not completely satisfied. I use TP20's with a wide variety of tip configurations at multiple index...
View ArticleAlignment problem I think?
I have try a few things with this program and still not sure how to fit it. I've been away from CMM Programming for about 4 years now, getting back into now. PC-Dmis 2013 B&S Global image. I almost...
View ArticleClik here to view.
2017R1 32 bits: 2 little "bugs"
I have 2 problems with this version : Patch scan : when I create a patch scan, the cmm measure it, and at the end, I have a error message that says there're no hit in the scan. This message appears for...
View ArticleHow To Add Operator Input to CSV format output File?
I am sending results from my program to a CSV file, the parts i am checking are from an eight cavity tool, so at the beginning of my program the operator is asked to enter a cavity number. Is there any...
View Article2017 _R1 sp1 - font size fix?
Has there been a fix for allowing the font size to be changed for the settings toolbar?
View ArticleOffline Programming - resetting to nominal
This is a large topic and I am only asking a couple of questions that I have come up with over the years.... I program almost all of my programs offline and upload the programs to a directory. The...
View ArticleRule of Thumbs
I've only programmed for a short 3 years but I made a list of rule-of-thumbs after working with PCDMIS and bridge CMMs. I'm assuming I have a fixtured part so that manual alignment is done only once...
View ArticleQuestions Adding SCR200 rack?
Hi guys, I have had this SCR200 rack physically installed on my CMM for about 6 months now and really need to get it going, I absolutely just haven't had the time. I've never done it, and was hoping to...
View ArticleCircle through two points
How to create circle through two points where dia is the distance between them?
View ArticleClik here to view.
Using a hole pattern as a Datum?
The drawing shown is an update of a part we make. Before the update the two holes through the bottom (A datum surface) were the B & C Datums. Now the two holes are the B datum and we have no C...
View ArticleCircle through two points with Diameter as Distance Between Them
How to create circle through two points where dia is the distance between them?
View ArticleArticle 6
Please post your code in the relevant thread within code tags. ie [code]insert code[/code]
View Article