Auto calibration without parameter sets
Hello, I'm currently trying to figure out a decent way to automatically calibrate the tips in the program without parameter sets. This program might be used on multiple machines in the future so I...
View ArticleScan: convert scan to points and then back to a scan again
Hi all, if i convert my scan into points , can I convert the points back to a can (using TP, prode)
View Articlegoing from 64 bit to 32 bit computer
Im getting a new PC, the old one was 64 bit win 7 and the new one is 32 bit win 7. Can I export the 64 bit settings then import back into the 32 bit computer? PcDmis 2014 release.
View ArticleDMO file configuration?
Still a little new to the PC DMIS world and I have a question for you gurus. The customer I'm dealing with wants a DMO file that only shows the Measured values from a specific alignment we setup. My...
View ArticleCircle (hole) on a curved surface
Say you had a pipe with very thin wall thickness and you wanted to pick up a 1 inch hole in the wall. What is the best way to do this? Normally I would use a gauge pin but in this case we can’t. There...
View ArticleClik here to view.
Weird probe changer picture
Hi, all, suddenly my probe changer picture showing strangely in my program. Please take a look the attached. I have checked the probe changer calibration data, restart the whole software. Nothing...
View ArticleClik here to view.
Clik here to view.
QDAS Help
Hello, I am trying to setup Q-DAS with PC-DMIS 2017. I am getting this error when I try to run a program. When I go into the configurator it asks me for a password which I don't have. Is there a...
View ArticleScan Reports Help
Good evening, I am working on a project to clean up reports. We run a shop floor cmm and a lab cmm. The shop floor is using Bladerunner. Whereas, the lab isn't. The problem I am having is with the...
View ArticleClik here to view.
Article 3
Hi guys. I ran this program some time ago (somebody else wrote it) & saw that alignment is made apparently out of nothing. Because the part is a disk there is nothing to stop it from spinning. So...
View ArticleClik here to view.
Alignment Out of Nothing/Auto Alignment?
Hi guys. I ran this program some time ago (somebody else wrote it) & saw that alignment is made apparently out of nothing. Because the part is a disk there is nothing to stop it from spinning. So...
View ArticleCollision detection to probe changer
Does any one has experience with collision detection to probe changer? I load a probe changer into my program, and move the probe tip to probe changer purposely. I ran the collision detection to see if...
View ArticleParallelism issue on 2017 R1 SP3
I have two measured planes (Tangente / minimax) and I need to measure the parallelism between them. The result is "0", but if I dimension the 3D distance between them the difference between min and max...
View ArticleClik here to view.
2015.1 SP10 , 2016 SP8... are on the ftp web site...
That's all, Folks ftp://ftp.wilcoxassoc.com/PC-DMIS-Ve...e/2015.1/SP10/ ftp://ftp.wilcoxassoc.com/PC-DMIS-Ve...ease/2016/SP8/
View ArticleClik here to view.
True position of hex nut?
I have a print that is calling out the True position of a Hex Nut, on top of the FCF it has the description of the Hex nut instead of a diameter size. Have any had to deal with something like this?
View ArticleConstructed point issue
So i have been having an issue with a certain construction involving an intersection of a radius with a line what im trying to do is make the 2 intersection that i have measured the walls as planes...
View ArticleClik here to view.
Just two questions about rotary tables...
Who uses it with PC-DMIS on Hexagon CMMs (BS, DEA, ...) Who at Hexagon works on PC-DMIS for rotary ? Thanks in advance answering here, please
View ArticleMaster vs hormonal (SCAN)
Hi everyone, I am doing an offline scan using open line and freeform, with TP200, should I select master or nominal and what is the difference?.
View ArticleChange highlight line thickness or show feature ID alive
Hi, all, Is there anyway to change highlight line thickness on features in the graphic window? The reason I want to do that is that when I edit my dimensions, I want to see right away which features...
View ArticleRenishaw Controller Scanning Parameters
Would anybody be able to tell me what they use for scanning parameters (probe options in parameters) on a Renishaw PHC 10-2 Controller? Thanks
View Article