Lmc
Maximum material condition: 1. For internal diameter: Bonus tolerance=( measured value- minimum diameter) + True position tolerance. 2. For external diameter: Bonus tolerance=( maximum diameter-...
View ArticleProtected Mode
When I open a program while in Protected Mode, I have to close the Edit window, the Report window and select Live view. Is it possible to set it up so that when a program opens, it opens to the live...
View ArticlePDF 'auto' asks where to save file after Windows update
Hi, I have measurement routines which stores pdf's with the 'auto' function and this worked always fine. The pdf's were always stored with a higher number, but after a windows update it always asks...
View Articletwo segment TP
Question guys. per sketch below, I have datum C with TPØ.005BA, would it be a legit callout if I have another segment bellow TP.003B. The intent is to isolate the location from -B- in a Z axis for the...
View ArticleSoftware Certification
Anyone have a copy of version 3.2 software cert (PTB or NIST) I could get a copy of? Closest thing I could find on the Hexagon website was 3.7.
View Article# Of Points for Adaptive Circle Scan
Good Morning, New to scanning. Took level 2 back in February. Tigo getting installed next week. Upgraded offline seat from 2016 CAD to 2018 CAD++ a few weeks ago. So i'm re doing my courses offline and...
View ArticleRepositioning a part during a program
Is it possible, when aligning off a cad model, to move the part and setup a whole new alignment. In the past I've always made an entirely different program for each different position. I now have a...
View ArticleRounding of measurement results?
Is there a way to tell PC-DMIS to stop rounding the measurement results ie drop the last decimal place? I know about displayprecision, but that still rounds the results up or down.
View ArticleAlignment
I have round part. Outside diameter is a cone and called out Datum-A and center bore is a cylinder and called out Datum-B. There is no datum C. How can I align this part ? Please suggest. I have...
View ArticleClik here to view.
Error message
Got this error message after running a part, saving and trying to re-take a feature. Running PC-DMIS2017 SP8.
View ArticleShuttle between Translate and Program mode
Is there a way to shuttle between "Program" mode and "Translate" mode using the Jogbox?
View ArticleProbe changer (MCR20)
Howdy folks. Help please....... I'm new to this machine, it's a B&S "one" running PCDMIS 2017 R1. It's been YEARS since I've programmed anything PCDMIS but memory has served me well I'm doing...
View Article"PC Dmis Message" Problem
Hi Everyone, I have a question in regards to the "PC Dmis" message window. Whenever I run my program in DCC mode, this window would always pop up notifying me about a tip change or a comment. I was...
View Articleprogramming a feature
Hey everyone, I have a job I am programming and I am a bit stuck on how to programme a certain feature on the part. I have attached photos and the feature in particular that I am struggling with is the...
View ArticleClik here to view.
CAD alignment, Z origin completely out
Can somebody let me know where i am going wrong. Lets take for example a block with 4 holes or which i have CAD. I'm looking to doing an auto circle (my start circle) for which the operator will take...
View ArticleArticle 1
Good afternoon, This is Darrollh from the forum. My number is 704-280-6071 and my email is cmmpro1@gmail.com.
View ArticleChanging hit points.
Help! Am self taught on PC-Demis and struggling with some issues. Have taught a program to the machine, run it twice. Then come to run again and "Hit points" have changed bearing no relation to...
View ArticlePC DMIS stops responding
I have the 2010 version mr1 cad ++. often stops responding. someone who can give some help will stop that Pc Dmis has a full cache and stops responding.
View Article