incorrect output
I have a problem when printing the correct value. The output should be dependent on which of the deviation of Z value is greater, and that one, must be displayed. In my code I always get the last of...
View ArticlePartial vs Full Calibration
Hi, We are using an SP25M SM25-1 setup on our CMM's. Production are asking about the cal times and is it possible to shorten. Is it worth mentioning partial calibration to them as an option? Is partial...
View Article2016.0 SP5 + FDC + LSPX1 = two probechange speeds
The SP5 for 2016.0 introduces the following: When a probe changer (such as the LSPX1) is connected to the FDC controller, it will use two speeds:Fast speed - PC-DMIS will use the move speed that is...
View Article"CPU Fail Error" What could have happened?
Good morning everyone. I was running a proven program on the CMM and went on break. I came back to this error on the CMM. TR_HWERR, CPU Fail Error [Fail Safe] ! I have never seen this error before and...
View ArticleUnable to load the PDF Drivers - PCDMIS 2015.1
I have a new desktop setup and I am getting this error message after writing my first program on this machine. The CMM was probably calibrated on another windows user account on this machine before I...
View ArticlePosition of angled cylinder
I have a part here with a call out of .008 to A/B/C. It is a through bore at an angle of 40 degrees. Datum A is the top surface of part, B is a diameter of 4.11 inches and C is a tapped through hole at...
View ArticleUser Files
In earlier versions, there was a folder that had subfolders for each user. Where is that in 2012?
View ArticleDisk Calibration
Hey all, it's been a little hectic with this disk probe and I don't know if you have came across this. My disk 18mm calibrates great but the diameter is off, I calibrate it with a ring gage and make...
View ArticleArticle 3
Hi, I read a post from 2007 about using a DM1 license for PcDmis. I tried opening a file with my DM1 license and the model is only in view mode. I cannot create anything with it. Has anything changed...
View ArticleArticle 2
Hi, I read a post from 2007 about using a DM1 license for PcDmis. I tried opening a file with a DM1 license and the model is only in view mode. I cannot create anything with it. Has anything changed...
View ArticleArticle 1
Hi Karen, I think you should add your question in the 2007 post, even if it's an old one, you will have a better view on answers !!!! Have a good week ! Jef
View ArticleArticle 0
I did, but hasn't been any activity from the original 'poster' in a long time. I can't even find RussL in the member list. DO you know anything about this? Or anyone who would? I'm new to posting and...
View ArticleClik here to view.
Article 2
I encountered Move Command Outside of Travel Limits error even though my part is mounted within the acceptable travel limit of the machine volume. I'm using B&S Excel 9-12-9 and PC-DMIS 2013 MR1....
View ArticleScan takes forever to start
Having an issue. Just upgraded PCDMIS and my PC to 64 bit versions. Whenever I use auto feature scans it takes PCDMIS forever it seems like to actually touch the part and start scanning. I have lowered...
View ArticleAcceleration during touch speed
Greetings, I think this is a bit of a stretch, but I would like to set the acceleration during touch in order to regulate ONLY X-axis touch speed. I have a thin part and am forced to use sample hits to...
View ArticleRound (tube) parts alignment (Romer Arm)
Dear forum members, does anybody can share his/her experience of round parts alinment when using a portable arm? I tried to align tube with two rounded slots and through holes but each time I faced...
View ArticleArticle 4
Hy sir plz tell me about iterative alignment. How it made and whyÂ*iterative alignment is done plz sir help. I thanks full to you Â*
View Articlei need a work around for the "Cancel" Button.
I have been searching for a possible solution to my problem and not had a whole lot of luck. For starters I have 7107 silver advantage CMM with 2014.1 PC DMIS. My problem is that i need a way to ask...
View ArticleCustom Report ColorMap Inclusion
If I create a coloured surface view using COP commands, is there a way to have that included in a custom report and will it automatically update the deviations in the program and the custom report as I...
View ArticleOperator versus Protected Modes
Continuing my saga of adapting the new and old and integrating the two. For those following, I did get my loop program to work quite well starting only with one read point and continuing the loop until...
View Article