keyboard command for taking hit
I might just be dumb, but is there a keyboard command to take a hit while in program mode. For example "alt -" erases a hit you took, but is there one to take the hit. I ask because in the CAD model I...
View ArticleProbe hitting part of job too soon.
Hi everyone, I am currently programming a job (see picture). One of the features on my job are the two pins as you will see. I have programmed these as auto cylinders, once I had programmed the part I...
View ArticleArticle 0
I run weekly calibrations on the CMM here, and there usually aren't any problems. Wednesday when I initiated the process I noticed that the RED LED didn't turn on when I pressed the green Machine Start...
View Article2017 r2 sp9
Here : http://software.hexagonmi.com/public...1340.0_x64.exe Release Notes - 2017 R2 SP9 • PCD-95827 - Fixed an issue where PC-DMIS did not create an alignment correctly for a datum feature when you...
View ArticleLocking out Calibration
Hey there. We have several CMMs that run 2010 MR3 and 2013 MR1. Five of our CMMs are all together and our sixth one, a Global Advantage, sits off by itself. It uses 2010 MR3. Long story short, we are...
View ArticleCMM To CMM program problems
I have version Cad++ Version 2017 R1 and my sister company has Version 2017 R2. Please tell me why when I share my programs with them (Pulling from a shared drive) That some of the measured features...
View ArticlePath lines
Hi all my path line only appears on the screen when I press the wheel on the mouse, it disappears after I remove my finger from the wheel. This makes it difficult to make adjustment to the auto feature...
View ArticleProbe Qual issue, 0,1,0 direction
I have a Probe Qual issue with the Qual Sphere mounted in the 0,1,0 direction. Thats "Straight back" or "to the back of the machine" for the rest of us. So i have a 90º tip that probes the bottom of a...
View ArticleMeasuring Threaded holes
Hi to all members I'm currently looking at best working practices of measuring threaded holes with a true position of 0.2 I would be grateful to get your idea's and method's on this subject . Cheers...
View ArticleAuto cylinder issues
Hi everyone, I have created an auto cylinder on a part I am programming, I have now completed the job and for some reason using the collision detection the probe seems to crash on the cylinders. The...
View ArticleHelp creating a custom report
Hello to all, I am reaching out to you folks with hope that someone can help me with a custom report. Our customer has been very specific in that they need us to provide them with a simple, no frills...
View ArticleAnalog Master Probe
Good Morning, I hate to add another master probe thread but I think this is a simple question which will get me a quick response. I've always chimed in on master probes threads to help ppl out not...
View ArticleSlow movingspeed..
hi all, after I have installed Pcdmis to a new pc, the speed became really slow, but the program has 300 mms and in F10 it is also 300 mms. When I move my probe with the jogbox its fast, but when the...
View ArticleClik here to view.
Average of the measurement rotated around the axis
Hello, I added vector points, one inside can and one outside can, I know the distance between them, then I rotated them by 15 degrees about the center of the coordinate system, now I have 24 pairs of...
View ArticleNjb jog box
Has anyone else had any problems with the new NJB jog boxes? We have had several go bad in the last couple years. You have to keep pushing the enable button harder and harder to jog the axis, until...
View ArticleClik here to view.
Article 1
Hi all, I may be about to display a total lack of some fundamentals, so please don't be too harsh... it may essay but i don't recall it. i check one hole dia 63.515/63.500 on pc-dmis 2012, with 13...
View ArticleCAD enquiry
Hey everyone, Programming a part (just finished) and carried out my manual alignments ready to run. So far the part seems to be running fine however there are a couple of features that seem to be in...
View ArticleClik here to view.
Odd Scan behavior, any ideas?
Pulling my hair out, trying to get a scan on this part. This screen grab is just the latest venture by the CMM for a linear open scan based on a cad model. Although never the same path, this is an...
View ArticleLeader Lines
I recently upgraded to 5.2 SP2 and I can't import the leader lines in through options then leader line settings. Is there a different way to import them in? Also using PC-DMIS 2018 R1 SP3
View Article