Illegal nuber of input features used error message
I was given a "working program" from one of our suppliers to run on our CMM. The machine I am running it on is a Sheffield D8 probe is a SM25-2 1mm by 20mm 2013 MR1. I keep getting an error message...
View ArticleAir Drye
Greeting ladies and gentlemen, I have a pretty substantial problem. I need to know how to drain the oil from the air dryers/ air filters.
View ArticleClik here to view.
cylinder diameter question
m measuring a cylinder using "Adaptive Cylinder Concentric Circle Scan" and MAX_INSCRIBED. when i dimension the cylinder i get a value different than dimensioning any of the levels separately. I would...
View ArticleVariable for Getting Part name
How can i grab the part name? Also for future reference how can i look up the variables being used for part name, REV number, SER number ect.... just shooting in the dark with GETPROGRAMINFO ("name")...
View ArticleAssigning the current Calibration Tool name to a variable.
I'm trying to automatically add the gage ID of the Tool used to my auto calibration program. Our metrology dept. switches them out a couple times a year to check them. Obviously I could have the...
View ArticleTomtheBomb is back again
Hello, I'm back again. I'm working in a small shop, I have very little time to spend here on the forum. I try to do the best that I can, the company has purchased another pcdmis (smaller unit pcdms...
View ArticleArticle 0
Sorry it has taken me so long to get back to you. It is the Legacy training block, but I had to talk to my local Hexagon rep. because it doesn't usually come with the program and results and results...
View Article2018 R1 sp1 circle gage still broken
I'm probably the only one who uses this feature, but it's still broke. (nothing works below .001 inch) Just an observation. Happy Easter.......
View ArticleDatums in aligments
I like to program with read points, then i do a rough dcc alignment and finally a final dcc alignment. My question is: 1) Should i be bothered by the fact that in my final dcc alignment i don't always...
View ArticleWhy does PC-DMIS have no official library in Python?
Why does PC-DMIS have no official library in Python? Tks!
View ArticleASME Y14.5 3 Point Datum Xact Measure
Happy Monday! I was told PC°Dmis automatically uses 3 point datum structuring for proper datum simulation - for example: Datum A, 'highest' three points, datum B highest 2 and datum C highest 1. etc.....
View ArticleCurved Slot Surface Profile
I have a print call out of surface profile to a curved slot in a casting. How would I go about completing the requested item? Just form a curved slot from points and then do a surface profile. Would I...
View ArticleClik here to view.
XACTMEASURE/ legacy and positions
why are my position measurements different using xact and legacy?
View ArticleGetting min and max point values between multiple planes
I believe I have found enough info to extract min and max point values from 3 separate planes. (When I hover over the variables line, I get the right number) Now I need to find the min and max point...
View ArticleSubroutine help
hello all, I am needing help with subroutines below is the list of code we are using and what we want to do is save the reports to a certain folder when the program is done running. I am having...
View ArticleGet tip angle
I apologize in advance if this has been covered, but I haven't been able to find anything. I have a ballbar program where I measure one point on each end of the bar and one point normal to the probe....
View ArticleNew style Jogbox issue.
I have the new style jogbox (H009834/) & when you take manual points in has "kickback" of probably .150". How do I disable this?? I have small parts & I can not take manual points in small...
View Articletertiary MMC bonus ?
DIM 127|128_2= POSITION OF CIRCLE CIR_128_1 UNITS=IN ,$ GRAPH=OFF TEXT=OFF MULT=30.00 OUTPUT=BOTH FIT TO DATUMS=OFF DEV PERPEN CENTERLINE=OFF DISPLAY=DIAMETER AX NOMINAL +TOL -TOL BONUS MEAS DEV OUTTOL...
View Article