http://software.hexagonmi.com/public...18_R1/SP6/x64/
With a very long release note![]( "Smile")
!
• PCD-120462 - Fixed a German translation error for Location dimension of
slots and edge points, L = L (slot length) and S = S (edge point-surface).
• PCD-125813 - When the pointcloud is not well aligned to the CAD model, the
resulting measured cross section (yellow polyline) may not be computed as
expected and may produce the incorrect shape. By default, the
PointcloudOperator CrossSectionCopCadCrossSectionDrivenByCad
registry entry is set to 1. It is possible to obtain better results by changing the
registry entry's value to 0 and recreating the cross section so that it uses this
new setting. This alternative way to calculate COP/CAD cross sections could
give better results when the medium distance between the cloud and the
CAD model is relevant in the section zone, and the nominal section is
strongly curved in this zone (distance is greater than 2 or 3 mm).
• PCD-126732 - Corrected an issue where a continuous scanning made with an
X1 probe was used to create a pointcloud surface colormap but the colors
were not displayed.
• PCD-131217 - Corrected an issue where the Mesh colormap scale with
percentages was not correctly shown on the report.
• PCD-138257 - Fixed an issue where PC-DMIS stopped working when
executing a measurement routine that already contained extra instances of
commands (extra instances of commands are created by executing the
measurement routine with commands such as Loops, Goto, etc.).
• PCD-144259 - Whenever you set a GD&T selection of a distance dimension,
the workplane that was added before was set up wrong, and the distance
dimension relationship and orientation were not set to match the distance
orientation, too. This issue has been fixed.
• PCD-145264 - Fixed an issue for the Leica LMF interface AT960 tracker where
the user could not save the first hit for a PNT with the CCR or T-Probe after
swapping from the LAS scanner.
• PCD-145623 - Fixed an issue where clearance plane paths were drawn in the
wrong orientation.
• PCD-147370 - Fixed an issue where the Mesh Colormap scale did not appear
in the Graphic Display window and the Text and CAD, CAD Only, and CADOnly
Landscape report templates.
• PCD-147697 - Fixed a rounding issue of the percentages shown on the
pointcloud colormap scale. The colormap scale now uses the number of
decimal places that are defined on the Dimension Display Precision
command (Edit | Preferences | Setup | Dimension tab).
• PCD-149014 - Failed to restore the original string if the expression failed. It
was saved in all uppercase letters, which was incorrect.
• PCD-149024 - For the Pointcloud Export function, the user can define the
separator used for the XYZ export. In the PC-DMIS Settings Editor, in the
PointcloudOperator section, use the ExportXYZSeparator registry entry.
The default value is a space: " ". Examples of separators are ";" and ",". Type
the separator without the quotation marks. If you type more than one
character, only the first one is used.
• PCD-149265 - Fixed an issue with certain quick-fixturing operations.
• PCD-149332 - Fixed an issue where, at times, the Surface Colormap could not
be reset from within the dialog box.
• PCD-149711 - Fixed scanning for the Zeiss direct machine interface.
• PCD-150013 - Corrected an issue when saving back to versions before
v2015.1 where not all of the global PRG variables would be read when that
PRG was loaded. The command data would be correct.
• PCD-150164 - Corrected an issue where the default printing file type could
change. This could happen without user intervention.
• PCD-150203 - Fixed a crash that occurred when the Constructed Feature was
selected and the measurement routine referenced a version 2015 "Attached
external measurement routine" that contained a pointcloud.
• PCD-150622 - Fixed an Enable Interpreter problem that caused a crash when
executing a basic script.
• PCD-150793 - Corrected showing the Exposure and Stripe Distance for Zeiss
Eagle Eye sensor in Offline mode.
• PCD-150889 - Corrected an issue for the LeicaLMF tracker when re-executing
a measurement routine with the LAS scanner, the program execution would
automatically go to next command after the first 1st scan pass was taken,
instead of waiting for the operator to click 'Scan Done'.
• PCD-151205 - Fixed an issue where PC-DMIS stopped working when the
Vision feature type was changed in the Edit window.
• PCD-151225 - Fixed an issue where the Pointcloud Colormap Max/Min
annotations were turned off when an Inspection Routine was closed, reopened,
and then re-executed.
• PCD-151346 - Fixed an issue where PC-DMIS may have stopped working
when the XactMeasure GD&T dialog box was closed.
• PCD-151985 - Fixed an accuracy issue that occurred when using
compensation files.
• PCD-152124 - The Insert rotary table move has to be able to insert the angle
unconditionally. The ending angle of the previous 4-axis scan differs from the
theoretical.
• PCD-152163 - I++ Auto Features - Speed and Point density from adaptive
scanning parameters are now correctly sent to the I++ server.
• PCD-152178 - Fixed Load Active Probe for I++ client. It loads the active tip (I++
Tool).
With a very long release note
!• PCD-120462 - Fixed a German translation error for Location dimension of
slots and edge points, L = L (slot length) and S = S (edge point-surface).
• PCD-125813 - When the pointcloud is not well aligned to the CAD model, the
resulting measured cross section (yellow polyline) may not be computed as
expected and may produce the incorrect shape. By default, the
PointcloudOperator CrossSectionCopCadCrossSectionDrivenByCad
registry entry is set to 1. It is possible to obtain better results by changing the
registry entry's value to 0 and recreating the cross section so that it uses this
new setting. This alternative way to calculate COP/CAD cross sections could
give better results when the medium distance between the cloud and the
CAD model is relevant in the section zone, and the nominal section is
strongly curved in this zone (distance is greater than 2 or 3 mm).
• PCD-126732 - Corrected an issue where a continuous scanning made with an
X1 probe was used to create a pointcloud surface colormap but the colors
were not displayed.
• PCD-131217 - Corrected an issue where the Mesh colormap scale with
percentages was not correctly shown on the report.
• PCD-138257 - Fixed an issue where PC-DMIS stopped working when
executing a measurement routine that already contained extra instances of
commands (extra instances of commands are created by executing the
measurement routine with commands such as Loops, Goto, etc.).
• PCD-144259 - Whenever you set a GD&T selection of a distance dimension,
the workplane that was added before was set up wrong, and the distance
dimension relationship and orientation were not set to match the distance
orientation, too. This issue has been fixed.
• PCD-145264 - Fixed an issue for the Leica LMF interface AT960 tracker where
the user could not save the first hit for a PNT with the CCR or T-Probe after
swapping from the LAS scanner.
• PCD-145623 - Fixed an issue where clearance plane paths were drawn in the
wrong orientation.
• PCD-147370 - Fixed an issue where the Mesh Colormap scale did not appear
in the Graphic Display window and the Text and CAD, CAD Only, and CADOnly
Landscape report templates.
• PCD-147697 - Fixed a rounding issue of the percentages shown on the
pointcloud colormap scale. The colormap scale now uses the number of
decimal places that are defined on the Dimension Display Precision
command (Edit | Preferences | Setup | Dimension tab).
• PCD-149014 - Failed to restore the original string if the expression failed. It
was saved in all uppercase letters, which was incorrect.
• PCD-149024 - For the Pointcloud Export function, the user can define the
separator used for the XYZ export. In the PC-DMIS Settings Editor, in the
PointcloudOperator section, use the ExportXYZSeparator registry entry.
The default value is a space: " ". Examples of separators are ";" and ",". Type
the separator without the quotation marks. If you type more than one
character, only the first one is used.
• PCD-149265 - Fixed an issue with certain quick-fixturing operations.
• PCD-149332 - Fixed an issue where, at times, the Surface Colormap could not
be reset from within the dialog box.
• PCD-149711 - Fixed scanning for the Zeiss direct machine interface.
• PCD-150013 - Corrected an issue when saving back to versions before
v2015.1 where not all of the global PRG variables would be read when that
PRG was loaded. The command data would be correct.
• PCD-150164 - Corrected an issue where the default printing file type could
change. This could happen without user intervention.
• PCD-150203 - Fixed a crash that occurred when the Constructed Feature was
selected and the measurement routine referenced a version 2015 "Attached
external measurement routine" that contained a pointcloud.
• PCD-150622 - Fixed an Enable Interpreter problem that caused a crash when
executing a basic script.
• PCD-150793 - Corrected showing the Exposure and Stripe Distance for Zeiss
Eagle Eye sensor in Offline mode.
• PCD-150889 - Corrected an issue for the LeicaLMF tracker when re-executing
a measurement routine with the LAS scanner, the program execution would
automatically go to next command after the first 1st scan pass was taken,
instead of waiting for the operator to click 'Scan Done'.
• PCD-151205 - Fixed an issue where PC-DMIS stopped working when the
Vision feature type was changed in the Edit window.
• PCD-151225 - Fixed an issue where the Pointcloud Colormap Max/Min
annotations were turned off when an Inspection Routine was closed, reopened,
and then re-executed.
• PCD-151346 - Fixed an issue where PC-DMIS may have stopped working
when the XactMeasure GD&T dialog box was closed.
• PCD-151985 - Fixed an accuracy issue that occurred when using
compensation files.
• PCD-152124 - The Insert rotary table move has to be able to insert the angle
unconditionally. The ending angle of the previous 4-axis scan differs from the
theoretical.
• PCD-152163 - I++ Auto Features - Speed and Point density from adaptive
scanning parameters are now correctly sent to the I++ server.
• PCD-152178 - Fixed Load Active Probe for I++ client. It loads the active tip (I++
Tool).